Tuesday, October 8, 2024
nanotrun.com
HomeMaterialsCarbide powderHigh Purity Hafnium Carbide HfC Powder CAS 12069-85-1, 99.9%

High Purity Hafnium Carbide HfC Powder CAS 12069-85-1, 99.9%

Hafnium Carbide, an inorganic material that has a high melting points is very resistant to wear and corrosion. It also resists oxidation in extreme temperatures (1100-1100°C).
Particle size: -325mesh

Purity: 99%


About


Hafnium Carbide HfC Powder:



Hafnium carbide HfC

This is a combination of carbon and hafnium.

Hafnium carbide


melting point

The melting point of this binary compound is approximately 3900degC. It is also one of the most resistant. However, it is not resistant to oxidation and can oxidize at temperatures as low or as 430°C.


Hafnium carbide

The HfO2 is a hard, black-gray, and brittle material. High cross-section absorbs the thermal neutrons. Resistivity 8.8mohm*cm. Used in nuclear reactor control rods. Preparation involves heating oil soot with H2 under H2 at 1900degC-2300degC. It can be used to form the crucible for melting oxide and other forms of oxide.

The improved spark plasmasintering (SPS), device was used for ultrafine carbonized Ha powder by carbothermal reduction reactions of HfO2 at 1650°C. It has a particle size of 125nm with an oxygen content below 0.5%. Powder purity is greater than 99.9%, with Zr being the exception. It is 99.6% when powder contains Zr impurities. The low synthesis temperatures, the rapid heating/cooling rates, and the current influence of the improved SPS procedure reduce intermediate reactions. This also minimizes particle growth. New synthesis methods allow for the production of large amounts of HfC (>175 g/day). HfC ceramics of high relative densities (>96%) can be obtained by SPS sintering at 2300°C for 30 minutes.

To receive the latest information, send us an inquiry

hafnium carbide price

Please fill out the form below if you wish to

buy Hafnium Carbide Powder



In bulk.


Hafnium Carbide HafC Powder Performance:

Hafnium Carbide powder is a gray metallic material. This is because it has the highest melting temperature of any compound. You can use it as an additive to cemented carbide, which has excellent characteristics like a lower and better thermal conductivity. This powder is also used widely in cutting tools, molds and rocket nozzle materials.


Technical Parameters of Hafnium Carbide HfC powder :

Hafnium Carbide powder Chemical Composition (%)
Please send me HfC Total C Free.C
HfC Powder 99min 6.3min 0.1max


It is simple.


Is Hafnium Carbide HfC Powder made?


You can prepare hafnium carbonide powder by reacting hafnium oxide and carbon at 1800-2500°C. In this case, it is necessary to take longer to get rid of all oxygen.

Hafnium carbonide is a dark gray, brittle liquid. This can be made by heating an alloy of elements or by reacting hafnium trioxide with methane at 2150°C. You can obtain sufficient amounts of hafnium tetrachloride or metal sponge in the production of zirconium at large scales for use in nuclear reactors. Industrially, you can make hafnium carbonide from hafnium oxide or metal sponges at between 1500 and 1700C. It contains almost all of the carbon theoretically required (6.30%degC), and as much as 0.1% free carbon (219). This hafnium-carbidide compound is not true stoichiometric, but it only contains a carbon solution at one interstitial point of the face-centered cubic lattice.

Hydrofluoric acid will dissolve carbonization, but it is inert at room temperatures. At 250-500degC, carbonization is exothermic with halogen to create hafnium Tetrahalide. It also forms hafnium Oxide with oxygen at 500degC. At higher temperatures, the hafnium carbonide will lose some carbon due to hydrogen.


Hafnium Carbide Uses:


Hafnium carbonide (HfC), which has the highest melting temperature of any binary alloy, has many high-temperature uses. HfC is a suitable candidate for extreme high temperature applications like rocket nozzles or scramjet components. You can use carbonization in hard coatings. This is often done using processes like plasma spraying. HfC structural can also be used to make high-temperature components and thermal insulation materials.

Hafnium carbonide (HfC), which has a melting point of 3890degC above, can be used as a refractory binary material. HfC or NBC may also be used in reactors as refractory materials. Ta4HfC5 mixed carbide has the highest melting temperature at 4215degC.

1. Hafnium carbide can also be added to cemented caride. This is widely used in the fields of mold making and cutting tools.

2. Hafnium carbonide can be used as rocket nozzle material.

3. Hafnium-carbid is used for nuclear reactor control rods. It’s an excellent metal to make nuclear reactor controlrods.

4. Used for making ultra-high-temperature ceramics

5.Reactant used to synthesize an organometallic hafnium-containing polymer

6.For coating.


Hafnium carbide HfC powder Storage Conditions


Hafnium Carbide HfC Pulp should be kept in a dry and clean environment.


Shipping Hafnium Carbide Powder – Packing and Shipping


You can pack it in two plastic bags with the inside.

Hafnium Carbide Powder Packaging: Vacuum packing 100g, 500g and 1kg/bag. 25 kg/barrel. Or as you request.

Hafnium Carbide HfC Powder shipping:


Could be sent by air, sea or express once payment has been received.

Robocup2009 advanced materials Nano Technology Co. Ltd.

High-quality products are what you want

Hafnium carbide


powder

Please feel free and contact us to make an enquiry. (

brad@ihpa.net

)


Hafnium Carbide Properties


Other Titles
hafnium(IV) carbide, hafnium monocarbide, HfC powder

12069-85-1

Compound Formula
HfC

Molecular Weight
190.5

Appearance
Black Powder

Melting Point
3900 degC

Boiling Point
N/A

Density
12.20 g/cm3

Solubility of H2O
N/A

Exact
191.946549


Hafnium Carbide Safety & Health Information


Signal word
N/A

Hazard Statements
N/A

Hazard Codes
N/A

Risk Codes
N/A

Safety statements
N/A

Transport Information
N/A




    RELATED ARTICLES
    - Advertisment -
    nanotrun.com

    Most Popular

    Recent Comments